HDD Sata boot problem - Версия для печати

HDD Sata boot problem - Версия для печати

+- DC-SWAT Forum (http://www.dc-swat.ru/forum)
+-- Форум: Sega Dreamcast (/forum-2.html)
+--- Форум: English section (/forum-29.html)
+--- Тема: HDD Sata boot problem (/thread-2473.html)

HDD Sata boot problem - zal16 - 22.08.2016 07:03

I'm trying to boot the dreamshell via HD + Sata IDE converter, the HD is recognized but does not start the program.
the following message appears:

Cheching for G1 ATA devices...
Found device with LBA48: 1953525168
Detected FAT32 filesystem on partition 0
Mounting filesystem....
FATFS: Error 5 in mounting a logical drive 0
Could not mount device as fatfs.

My HD is Seagate sata 2.5" 1TB in FAT32 format with proper "DS" folder.

RE: HDD Sata boot problem - Gillbert - 23.08.2016 01:15

(22.08.2016 07:03)zal16 писал(а): I'm trying to boot the dreamshell via HD + Sata IDE converter, the HD is recognized but does not start the program.

Does it work ok with an IDE HDD?
How did you performed the IDE mod? Did you use kynar wires or a IDE cable directly soldered on the DC modo? What kind of SATA bridge are you using? Give us more details about your mod.

Anyway, this problem can be related to the wiring, I already faced this symptom.
Check the length of the wires and take a special attention for the GROUND connections.

RE: HDD Sata boot problem - aldair - 23.08.2016 01:45

(22.08.2016 07:03)zal16 писал(а): I'm trying to boot the dreamshell via HD + Sata IDE converter, the HD is recognized but does not start the program.
the following message appears:

Cheching for G1 ATA devices...
Found device with LBA48: 1953525168
Detected FAT32 filesystem on partition 0
Mounting filesystem....
FATFS: Error 5 in mounting a logical drive 0
Could not mount device as fatfs.

This is the Dreamcast za16:
A good job in adapting the IDE, and even then the adapter does not work fully!

sata working perfectly:

My HD is Seagate sata 2.5" 1TB in FAT32 format with proper "DS" folder.

RE: HDD Sata boot problem - SWAT - 23.08.2016 09:59

(22.08.2016 07:03)zal16 писал(а): I'm trying to boot the dreamshell via HD + Sata IDE converter, the HD is recognized but does not start the program.
the following message appears:

Cheching for G1 ATA devices...
Found device with LBA48: 1953525168
Detected FAT32 filesystem on partition 0
Mounting filesystem....
FATFS: Error 5 in mounting a logical drive 0
Could not mount device as fatfs.

My HD is Seagate sata 2.5" 1TB in FAT32 format with proper "DS" folder.

Looks like bad formatting. HDD detected, boot sector reading normally (it's found partition with fatfs), but at mounting fs something went wrong.

RE: HDD Sata boot problem - zal16 - 03.10.2016 23:26

The above mod (criticized by @Aldair), is still working, the problem is the bad formmating (mentioned by @SWAT). Beacuse i formmated this HD on a bad quality Sata to USB converter, not recognizing in the Dreamshell. The solution are formmating directily o a SATA port on my PC.

RE: HDD Sata boot problem - aykiri1 - 23.12.2016 22:09

i have similar problem. Found LBA48 device and freeze... and cable is not so long
need help thx.

http://i.hizliresim.com/8Pd9kk.jpg

http://i.hizliresim.com/LZnYjJ.jpg

RE: HDD Sata boot problem - aldair - 24.12.2016 00:03

(23.12.2016 22:09)aykiri1 писал(а): i have similar problem. Found LBA48 device and freeze... and cable is not so long
need help thx.

http://i.hizliresim.com/8Pd9kk.jpg

http://i.hizliresim.com/LZnYjJ.jpg

RE: HDD Sata boot problem - aykiri1 - 27.12.2016 23:05

hi i changed to cables
http://i.hizliresim.com/g29dL2.jpg

its working success !
thx