DreamShell Compatible 44-Pin IDE-to-SATA & SD-to-SATA Adapters

[pcwzrd13]

I bought this IDE-to-SATA adapter a couple years ago and I could never get it to work but I found the solution today! Turns out all I needed to do is cut pin 1 and bridge JP1 (HDD Select) on the board. Now it works perfectly! If anyone is looking for a cheap 44-pin IDE-to-SATA adapter, this is the one to get! The model on the chip is JM20330.

https://ebay.us/jQDi6B



Edit: Found a SATA-to-SD adapter that works as well! Unfortunately it doesn't support LBA28 so it won't work with the 0.7.X loader. No problems booting DreamShell from it or using the 0.6 loader though.

https://ebay.us/j512Mt

[pcwzrd13]

Found a SATA-to-SD adapter that works as well! Updated the first post with details.

[megavolt85]

IDE->SATA->IDE->SD

SATA2SD use JM20330 for conversion SATA2IDE

[pcwzrd13]

(07.11.2019 03:22)megavolt85 писал(а):  IDE->SATA->IDE->SD

SATA2SD use JM20330 for conversion SATA2IDE

I noticed that.

[linerty]

I found ide2sd on one brige: IDE 2,5 "44 Pin https://a.aliexpress.ru/_etrGBi
Chip: Sintechi 1309
UDMA2, FAT16 not supported, sd more 128GB not supported. Datasheet not found.

Spoiler (Click to View)

Review.
As I understand it, it works in master mode. But this does not mean that there is no slave switch.

[elpedromolina04]

(07.11.2019 03:22)megavolt85 писал(а):  IDE->SATA->IDE->SD

SATA2SD use JM20330 for conversion SATA2IDE

hello megavolt! will this ide sata adapter work? has jumper for slave master , it's from startech

https://www.aliexpress.com/item/33046605120.html

https://articulo.mercadolibre.com.ar/MLA...3b6b209b0b

[megavolt85]

(19.02.2021 07:24)elpedromolina04 писал(а):  hello megavolt! will this ide sata adapter work? has jumper for slave master , it's from startech

this adapter for connect two SATA to one IDE
it occupies the entire bus and does not allow working with the GD drive

[elpedromolina04]

(19.02.2021 08:57)megavolt85 писал(а):  [quote='elpedromolina04' pid='41356' dateline='1613705080']
hello megavolt! will this ide sata adapter work? has jumper for slave master , it's from startech

Uhhh, what a shame, I'll look for another one, the problem is that it is expensive to buy the green sata ide adapter, either of the two models, here in Argentina, this yellow sata ide that I showed you is really cheap, but hey, bad luck, Thank you very much for answering!!

[dimka112]

(12.10.2019 20:29)pcwzrd13 писал(а):  I bought this IDE-to-SATA adapter a couple years ago and I could never get it to work but I found the solution today! Turns out all I needed to do is cut pin 1 and bridge JP1 (HDD Select) on the board. Now it works perfectly! If anyone is looking for a cheap 44-pin IDE-to-SATA adapter, this is the one to get! The model on the chip is JM20330.

Спасибо. Тоже валялся адаптер, ни как не хотела Дримка видеть Sata-шный HDD. Ни джамперов, ни плошадок выбора не было. Поднял 16-ю ногу (RESETn) на JM20330 и на 33-ю ногу (MSSEL) кинул 3.3в. И о чудо, дримка его увидела. Еще раз спасибо!
  20210421_221727.jpg (Размер: 395.92 Кб / Загрузок: 62)