89 Name: Chao Posted: November 21, 2008 (Fri) 14:11 ID: O.5SCAUc
Dreamcast SD Rip ver1.0 release.
吸出Shimasu Dreamcast with the SD card by itself does not depend on the OS.
GD-sucking time is the total mass is about 35 minutes ROM.
Suction type of data tracks are raw bainary same httpd-ack.
In all 吸I出Shimasu bulk suction track.txt / disc.gdi / info.txt / ip.bin / all track.
If not enough disk space on the way new SD card also supports splitting files.
The Dreamcast also supports the CRC does not match then corrected to the correct data.
The SD card is directly connected serial port of the Dreamcast.
(SD card you use, it is best to split the file is not necessary 2G).
Since the serial port attached to the larger EMI suppression capacitors on some Dreamcast may not work.
Works fine by removing the corresponding capacitor case.
(Please refer to drawing pictures on the same page).
ttp: / / f17.aaa.livedoor.jp / ~ takotako/dcserial_ft232bm.php # dcsdrip
90 Name: Chao Posted: 2008/12/02 (Tue) 15:02 ID: O.5SCAUc
I write a few questions I had about the Dreamcast SD Rip ver1.0.
Q: Where to get the price of the SD Card Connector?
A: I have one available at 150 yen on electronic trading Akizuki.
Q: Dreamcast unit of EMI suppression capacitors are removed, it is better to do?
A: without error writing to the SD card is also OK to disconnect if it works properly.
Q: MMC card be used?
A: MMC card is not available. SD card (SD / miniSD / microSD) is available.
2G SD card is recommended do not need to fill and then split.
Q: when inserting or removing the SD card?
A: You can disconnect at any time if the access is off LED.
Q: I split files?
A: If the disk becomes full while writing a file and writes the remaining data to replace the SD card.
Extension of the split files are numbered sequentially as .001 and .002.
The output of the batch file to convert the original file at the end.
Example) When the disk becomes full while sucking track03.bin
The output file for track03.bin: track03.001 track03.002 track03.bat
Batch file contents: type track03.bat
copy / b track03.001 + track03.002 track03.bin
Please run the batch file to copy the necessary files on hard disk space.
91 Name: Chao Posted: 2008/12/15 (Mon) 13:47 ID: 2o3.P3g.
Dreamcast SD Rip ver1.1
ver1.0 => ver1.1:
. Adding iso image rip mode.
Add a directory listing of the SD card.
92 Name: Tan Post Gates: 2008/12/26 (Fri) 07:37 ID: gBJSD5a2
Sucking on 出Seru simple circuit so the SD is like to make immediately enters the catcher I get good cards
^ ^ It is buy another one for the suction is also DC
93 Name: Chao Posted: 12/31/2008 (Wed) 02:46 ID: TfRT10Ew
The last Palm disc.gdi file "0" Temashita missing.
Leave a modified version of 1.1 dcsdrip11.lzh swapped. (12/31/2008)
Please try AA Gates evening.
I'm sorry that Mr. Marin I report on experiments with tight again!
94 Name: 71 Posted: 2009/01/01 (Thu) 14:18 ID: WUDYWg9w
Happy New Year!
I had a long time I was allowed to peek into your site as a link to the site of Chao Makaron.
Ripping in SD and what is possible!
Immediately, we can create problems Ripping.
DC is using the parallel port have failed in previous rip, SDRip is Ikemashita problems.
1400 yen SD card because it was something in the neighborhood of 4G, buy it.
Dumped in the trial of the "Incoming" was 40 minutes in 1.19G.
httpd-I was using the ack,
1, the PC must be started simultaneously with the DC.
Two people in the home must be wired in a situation that is wireless.
For example, recently it was not ripping Mendokusaku.
This way, you can crisp it alone ripping DC, and I think very useful.
Incidentally, did not require removal of the capacitor.
95 Name: Chao Posted: 2009/01/05 (Mon) 18:39 ID: TfRT10Ew
Happy New Year!
71's evening
No more ripping tool I thought no need to make again.
SD media is, SDHC is not officially compatible to
May be used for up to 4G.
Applies to SD cards up to 2G uniform.
> The link to the site of Chao Makaron site
GD Temashita I make FPGA-ROM emulator on!
G1 with respect to port, but the situation still does not look even pinout, I thought I want to make Once you have the time.
(From overseas port is no documentation on G1? Temashita what came through the mail or that.)
GD-ROM emulator or an SD Loader Once I leave it to there and then build.
96 Name: Chao Posted: 2009/01/07 (Wed) 01:25 ID: TfRT10Ew
We also tested Transcend SDHC 8G.
The 16G SDHC have not tried it yet, the reports from abroad
Yes was the NG.
4G and 8G are still some manufacturers may not work there.
97 Name: 71 Posted: 2009/01/07 (Wed) 22:58 ID: WUDYWg9w
I also did not describe specific information is added.
I used the SDHC 4G is intended for Buffalo. MB-RSDC-was 4G.
The DC unit manufactured in 1998, the Northeast is the TKR.
And will be used to 8G, and created a Directory on Disc titles such as when Ripping, such as happy as you want to be Rip.
We also expected to SD loader.
The
98 Name: 77 Posted: 2009/01/11 (Sun) 03:08 ID: uyWW5r / w
SDRip, I tried to report it worked to create.
I think that's also very well buy an SD card with solder connectors
I soldered directly to the terminal portion of Geta to convert to SD size Buy bonus that comes with microSD. (Omission)
He worked in a room with a microSD cheapest I sell a certain Dosupara Tokaiu Apacer.
Wiring really handy, and shiny and faster and Interesting.
Incidentally, an electrolytic capacitor used a slightly larger size fit properly without both (220μF certainly), it was okay.
Thank you very interesting things.
99 Name: Chao Posted: 2009/01/11 (Sun) 16:54 ID: TfRT10Ew
Hello, I 77
> The Geta to convert to SD size microSD comes with a bonus Buy
> I soldered directly to the terminals. (Omission)
It is good working.
You think you may have previously borrowed on behalf connector conversion adapter I guess the same is also
I write to then I had a question about the reliability and then write.
SD card interface and SPI interface is
SD card during initialization (initialization of communication) in the command sequence to ON mode, the CRC check 7bit, read and write sectors is 16bit
And to ensure reliable communication in the CRC.
Res to: 71
> And will be used to 8G, such as when the title of Disc Ripping
> Create a Directory, such as happy as you want to be Rip.
I was the target subdirectory up to 2G SD did not think at first, but I think let's consider the following when upgrading.
100 Name: turbo not there Posted: 2009/02/09 (Mon) 08:54 ID: N Money There
Com N there
101 Name: Chao Posted: 2009/04/09 (Thu) 17:10 ID: RwBCaR.s
Dreamcast SD Loader ver1.0
I made a simple SD loader anyway Dreamcast does not play with little busy work days.
An executable file extension ELF file / Motorola hex file /. Hex bin file to ELF file is determined by the contents of files regardless of extension.
. Bin files are treated as binary files in the Start Address 0x8c010000.
You can choose a flat binary or binaries that are scrambled.
ttp: / / f17.aaa.livedoor.jp / ~ takotako/dcserial_ft232bm.php # dcsdload
102 Name: Tan Gates Posted: April 12, 2009 (Sun) 21:09 ID: R6XVrGtw
>> Do Chao
I'd like to ask you about the Dreamcast SD Loader, that the files on the SD card bootable I would also start the emulator is also available as NesterDC.
(SDRip not created yet, so)
Since I was in the mood had been talking about recent overseas sites.
ttp: / /
http://www.dreamcast.es/news.php?readmore=249
103 Name: Chao Posted: 2009/04/13 (Mon) 15:46 ID: RwBCaR.s
System calls such as SD Loader dctool only features currently do not have a pure loader.
I will be made to reduce the size considerably, no longer can afford to put a system I call compatible dctool.
> What you can also start the emulator as well NesterDC.
The very start is possible, and necessary data to the emulator ROM
CD-R (GD-DRIVE) side is required.
Basically, you must re-enable existing applications to the SD card.
As a way of moving an existing application as it would be difficult because GD-resident loader can narrow space There is a way to emulate the ROM.
(GD if possible - but this is also how I can boot from the SD backup of the ROM)
> I was not in the mood had been talking about recent overseas sites.
Send mail had come from an SD card adapter for the Spanish team since last August.
The SD card library was around Christmas so I'm not making anything, but I thought, Did I make I SD card adapter!
Since they are making an emulator for the DC, the emulator will come out the SD card out of it.
Originally published as an example but it is not easy to connect to the DC serial port removable storage, 500KBytes/SEC read / write speed of the
Depending on the application because the response may be more than many think.
104 Name: 102 Post Date: 2009/04/13 (Mon) 20:36 ID: R6XVrGtw
> Very start is possible, and necessary data to the emulator ROM
CD-R (GD-DRIVE) side is required.
It is still such a thing.
I SDRip Let's create a future release will support in preparation for application.
Thank you.
105 Name: Tan Gates Posted: 2011/06/11 (Sat) 14:18 ID: RNavFbEI
You can pick up the problem in the SEEK draft errors?