Создать ответ 
 
Рейтинг темы:
  • Голосов: 0 - Средняя оценка: 0
  • 1
  • 2
  • 3
  • 4
  • 5
JM20330 board without M/S jumper compatible w/ Dreamshell
Автор Сообщение
Gillbert Не на форуме
Продвинутый
***

Сообщений: 127
Зарегистрирован: 10.08.2014
Рейтинг: 4
Сказал спасибо: 30
Поблагодарили 54 раз(а) в 34 сообщ.
Сообщение: #1
Лампочка JM20330 board without M/S jumper compatible w/ Dreamshell
I just like to share a solution for a problem, maybe someone is in the same boat. Smile

I had bought some of these IDE-SATA adapters from eBay years ago but unfortunately they don't have a master/slave select jumper so that it was impossible to use them along with Dreamcast/Dreamshell, as everybody knows that the device must be set as slave mode in order to work.

[Изображение: 2h4kcps.jpg]

It's a Jmicrom JM20330 chipset based board. I was pretty sure this chipset was indeed compatible with DC since I have used other different boards with same chipset and they work fine, so I decide to investigate a little and compared the boards and I then was able to understand how to enable the M/S jumper selection from JM chip.

Note that there is a mark in the board called"SW1" which initially I thought could be a M/S select but it has nothing to do with mode selection:

[Изображение: 6z8n5f.jpg]

I found that the pin 33 is the one responsible for M/S select mode. The incompatible board had this pin soldered to ground (low state) so that it only operated in master mode. In order to enable slave mode this pin have to be assigned to an high state (3,3V).

[Изображение: fva8w3.jpg]

[Изображение: o5s0f9.jpg]

I lifted pin 33 from board (it was a bit tricky job...), added a 1K resistor and wired it to a 3,3V point (I used the out pin of a 3V3 voltage regulator). Now the slave mode was successfully enabled. Smile Later I completed the mod adding a jumper board in order to choose between M/S modes:
[Изображение: 24awmyd.jpg]


Here's a diagram for illustrating the mod:
[Изображение: 2cdwxty.jpg]


Cheers!
(Последний раз сообщение было отредактировано 25.07.2017 в 20:51, отредактировал пользователь Gillbert.)
29.06.2016 22:05
Найти все сообщения Цитировать это сообщение
 Сказали спасибо: SWAT , aldair , boxcutter , LEUMAS , Armorant
boxcutter Не на форуме
Пользователь
**

Сообщений: 22
Зарегистрирован: 18.12.2014
Рейтинг: 0
Сказал спасибо: 3
Поблагодарили 0 раз(а) в 0 сообщ.
Сообщение: #2
RE: JM20330 board without M/S jumper compatible w/ Dreamshell
good info.

acording to the datasheet the chip has an internal pulldown resistor, so they had no need to ground the pin anyway!


Прикрепления
.pdf  JM20330_Spec_Rev. 2.3.pdf (Размер: 1.56 Мб / Загрузок: 61)
03.07.2016 00:27
Найти все сообщения Цитировать это сообщение
Создать ответ 


Похожие темы
Тема: Автор Ответов: Просмотров: Посл. сообщение
  Dreamshell problem dont allow me to change Loader Device SheepRaider 4 3541 25.08.2022 15:57
Посл. сообщение: SheepRaider
  DreamShell Compatible 44-Pin IDE-to-SATA & SD-to-SATA Adapters pcwzrd13 8 14289 21.04.2021 23:32
Посл. сообщение: dimka112
  dreamshell bios flasher cannot detect bios chip chth96 4 6438 01.04.2021 16:14
Посл. сообщение: chth96
Фото Korean GD-ROM board Gillbert 4 13849 10.04.2020 18:44
Посл. сообщение: zeigren
  Конвертация русской пиратки для Dreamshell Eugeniy_59 0 4778 03.09.2018 23:33
Посл. сообщение: Eugeniy_59
  Вопрос по sd mod и Dreamshell FreddyFreed 7 23559 24.10.2016 13:14
Посл. сообщение: SWAT
Хорошо IDE-SATA adapter fully compatible with Sega Dreamcast. nem 2 13184 22.07.2016 11:12
Посл. сообщение: boxcutter
  Katana V2.1 Main Board special 4 33926 02.10.2014 11:06
Посл. сообщение: MetalliC

Переход:


Пользователи просматривают эту тему: 1 Гость(ей)