+- DC-SWAT Forum (http://www.dc-swat.ru/forum)
+-- Форум: Sega Dreamcast (/forum-2.html)
+--- Форум: English section (/forum-29.html)
+--- Тема: Fix Problem Sata/Ssd (/thread-3061.html)
Страниц: 1 2
RE: Fix Problem Sata/Ssd - dragoncity - 17.02.2018 22:43
(17.02.2018 22:41)aldair писал(а):(17.02.2018 22:01)dragoncity писал(а): Hum ok.. do you have an exemple of problem because I tested 4 adapter.. and play 3 games no problem.
Even without pin 1, I still need the SD card to load the IDE.
No,I tested I can boot Dreamshell without Pin 1 no problem in CF
I Will test in SSD,but I use an SD for Preset
Ho Ok Strange I tested in CF no problem without Pin 1 for boot !
But with SSD need an SD... crazy ^^ !
RE: Fix Problem Sata/Ssd - dragoncity - 17.02.2018 23:47
So WITHOUT PIN 1 with SSD (or SATA)
- If you don't use GDROM (with nogdrom bios),you need to boot with SD !
- If you use GDROM you can boot with dreamshell on the SSD (or SATA).
RE: Fix Problem Sata/Ssd - Gillbert - 18.02.2018 00:17
Well, that's the problem, we still need the serial SD Card if want to use noGDROM.
RE: Fix Problem Sata/Ssd - dragoncity - 18.02.2018 00:19
Yes... for me not really a problem because preset doesn't work with IDE... so for me SD it's obligatory for the moment..
But It's sure I prefer that work with NoGdrom.
RE: Fix Problem Sata/Ssd - Gillbert - 18.02.2018 00:42
In my case it does not change much because I was already able to get my SATA adapters working here without GDROM board, I just need to make a clean and organized wiring. *But, with a serial SD Card reader*. If I use a GDROM board, no problem.
So, the main problem still remains. The proper solutions should be:
- A custom PCB design for JM20330 controller;
- A bootloader bios which is able to boot on Master mode.
RE: Fix Problem Sata/Ssd - Rellikami - 16.06.2018 23:10
this makes most adapters work i think, i had these https://www.amazon.com/HDE-Computer-Drive-Interface-Adapter/dp/B008X8NK0I with the IDE2SATA chips that didn't detect at all work and my JM20330 ones booted all the way into Dreamshell with pin 1 removed.
only issue i am having is shenmue II doesn't boot from Sata where as it does from CF, don't know about SSD since i don't have a spare one to test it out.
I have a GDROM that works though and boot with DS boot cd.
RE: Fix Problem Sata/Ssd - fafadou - 17.06.2018 12:44
Normally, the next of dreamshell / DS folder will be able to have two hdd and I hope one in master mode, for me some games will works better because we can install a better convert ide-sata.
RE: Fix Problem Sata/Ssd - Rellikami - 20.06.2018 05:41
I tried a new SATA drive today, was a 500gb HGST Travelstar laptop drive sold to go in a ps3 with the caddy attached.
i got it on discount at walmart for $25, works loading all my games even shenmue II so guess dreamshell doesn't like certain sata drives as well as sata2ide adapters.
Guess i will make this one my daily driver for testing things.
RE: Fix Problem Sata/Ssd - fafadou - 20.06.2018 12:27
Well done :-)
RE: Fix Problem Sata/Ssd - Coaster - 19.04.2019 23:56
Thankyou Megavolt for the 10K resistor advice on Pin 1. I have all my SATA adapters I purchased working great now
(19.04.2019 23:56)Coaster писал(а): Thankyou Megavolt for the 10K resistor advice on Pin 1. I have all my SATA adapters I purchased working great now
RE: Fix Problem Sata/Ssd - yoppie - 24.02.2020 20:52
(19.04.2019 23:56)Coaster писал(а): Thankyou Megavolt for the 10K resistor advice on Pin 1. I have all my SATA adapters I purchased working great now
(19.04.2019 23:56)Coaster писал(а): Thankyou Megavolt for the 10K resistor advice on Pin 1. I have all my SATA adapters I purchased working great now
how to connect resistor 10k on pin1, can you give a picture
RE: Fix Problem Sata/Ssd - Anderson - 30.10.2020 11:08
(17.02.2018 21:48)megavolt85 писал(а): connect reset via 10k resistor to VCC
hi friends, does anyone know where the VCC is?
Thanks for helping
If you are having trouble with your converter working, you can:
connect Pin 1(reset) via 10k resistor to VCC
RE: Fix Problem Sata/Ssd - megavolt85 - 30.10.2020 20:41
VCC is power +3.3 Volts
RE: Fix Problem Sata/Ssd - Anderson - 31.10.2020 00:41
(30.10.2020 20:41)megavolt85 писал(а): VCC is power +3.3 Volts
thanks for answering MegaVolt, so this is the correct connection?
Note, my motherboard is a VA0
[attachment=992]
RE: Fix Problem Sata/Ssd - megavolt85 - 31.10.2020 04:44
(31.10.2020 00:41)Anderson писал(а): so this is the correct connection?
yep
RE: Fix Problem Sata/Ssd - Anderson - 31.10.2020 05:45
(31.10.2020 04:44)megavolt85 писал(а):(31.10.2020 00:41)Anderson писал(а): so this is the correct connection?
yep
Thank you MegaVolt, thank you for your help, I will test it on my Dreamcast VA0
RE: Fix Problem Sata/Ssd - Anderson - 02.11.2020 04:37
(31.10.2020 04:44)megavolt85 писал(а):(31.10.2020 00:41)Anderson писал(а): so this is the correct connection?
yep
MegaVolt one more question friend, in my Dreamcast VA0, I will leave the GDROM connected to run games via CR-ROM, and I will leave connected the IDE / Sata mod with a 256GB SSD, leaving the connection from pin 1 to the 10k resistor to the VCC as shown in the photo, I could have a problem, I say my GDROM card can burn or have problems?
Thanks for answering
RE: Fix Problem Sata/Ssd - megavolt85 - 02.11.2020 19:54
it is not dangerous for GDROM
RE: Fix Problem Sata/Ssd - Anderson - 03.11.2020 00:17
(02.11.2020 19:54)megavolt85 писал(а): it is not dangerous for GDROM
thank you great MegaVolt